1,575
edits
Changes
no edit summary
==Grocery List==
*I'm sure I'm missing stuff from this list but it's a damn good start!
*Radio
**HAM Gear
***Drill (preferably a Drill Press)
***Counter Sink Bit
***#7 Drill Bit
*Antenna
**Hardware
***Zip Ties
***Adhesive Zip Tie Mounts
***The following parts from Digikey (includes a few spares)
****3x [http://www.digikey.com/product-search/en?x=0&y=0&lang=en&site=us&KeyWords=WM2245-ND WM2245-ND]
****3x [http://www.digikey.com/product-search/en?x=0&y=0&lang=en&site=us&KeyWords=WM2240-ND WM2240-ND]
****10x [http://www.digikey.com/product-detail/en/42817-0011/WM6459CT-ND/2816112 WM6459CT-ND]
****5x [http://www.digikey.com/product-detail/en/42815-0011/WM1947-ND/283491 WM1947-ND]
****15x [http://www.digikey.com/product-detail/en/42817-0041/WM6460CT-ND/2816113 WM6460CT-ND]
****10x [http://www.digikey.com/product-detail/en/42815-0041/WM6457CT-ND/2816110 WM6457CT-ND]
****1x [http://www.digikey.com/product-search/en?x=0&y=0&lang=en&site=us&KeyWords=WM5721-ND WM57210-ND]
****1x [http://www.digikey.com/product-search/en?x=0&y=0&lang=en&site=us&KeyWords=WM4424-ND WM4424-ND]
***5x [http://www.ebay.com/sch/i.html?_trksid=p5197.m570.l1313&_nkw=bosche+relay&_sacat=0&_from=R40 Bosche Style Relays]
***5x [http://www.ebay.com/sch/i.html?_trksid=p5197.m570.l1313&_nkw=bosche+relay&_sacat=0&_from=R40 Bosche Style Relay Harnesses with Pig Tails]
**Tools
***Heat Gun
#Check the area below the cable for a gap. If there is a gap there, pull the cable back and put some more Liquid Electrical Tape there and let it dry.<br />[[File:Yaesu_Install_NMO_Mount_7.jpg|400px]]
#Put 1 last coat over the whole thing and work up the cable an inch or so (this is to provide some additional strain relief). Let it dry.<br />[[File:Yaesu_Install_NMO_Mount_8.jpg|400px]]
#Now it's time to reattach the bracket to the Strut Channel. I also decided to Zip Tie the cable to the nearest spacer bolt as additional strain relief. If you chose to buy an NMO Weather Cap, install it until you're ready to put your NMO Antenna on. The silver you see on the center pin of my NMO Connector is a bit of solder I used when trying to heat up the center pin. It's flat and shouldn't cause any problems. Congrats! You're done with the NMO Mount!<br />[[File:Strut_Channel_No_Glue_1Yaesu_Install_NMO_Mount_9.jpg|400px]][[File:Yaesu_Install_NMO_Mount_9Yaesu_Install_NMO_Mount_10.jpg|400px]][[File:Yaesu_Install_NMO_Mount_10Strut_Channel_No_Glue_1.jpg|400px]]
===The PowerDistribution & Relay Plate=== Coming Soon! ===Power Wiring===
Coming Soon!